Datamax manual

Troubleshooting help from experts and users. Ask our large community for support. USB plug and manual as well This is barely used datamax m class lable printer.

View and Download Datamax Printer I manual. Datamax user guides and manuals. User manual for the device Datamax I-Class I Ademco vista 20p user manual. Datamax Printers. Manuals Directory ManualsDir. Datamax manuals. Verify that the AC. Same as Parallel Port A, for an optional Ethernet connection. ADAPTER menu, the printer may have active print requests or multiple users may be trying to access these parameters for example, during simultaneous telenet sessions.

Network Interface Card Adapter optional. After this process, you will be able to configure the options provided using the menu system. No part of this.. Depending upon the operating system of your host computer, installation may differ slightly. Consult the additional documentation supplied with this option for detailed information. The USB Port is plug and play and operates transparently within the printer; there are no menu-selectable settings or modes.

The USB Port is a device-end only printer connection. Never connect a keyboard, mouse, modem, etc. To use 1. Close the Access Cover. If using less than full width media, adjust the Leveling Cam; see Section 5. If using reflective stock, ensure that the mark is facedown. The Media Sensor needs to be positioned so that the printer can detect the presence of media and the top-of-form except for continuous stock, where the TOF is set through programming; see Label Length, Section 4.

To adjust:. Ribbon is required with thermal transfer media. To load:. Otherwise, lower the Printhead Assembly and rotate the Printhead Latch completely back into the locked position. When the supply is exhausted, pull the empty core from the Ribbon Supply Hub and discard it. To remove used ribbon: grasp the Ribbon Take-Up Hub, pull outward, then squeeze to collapse the hub and take off the ribbon.

These types are NOT interchangeable for use with the printer. At the factory, the printer is calibrated to sense a wide range of media types. Quick Media Calibration fine-tunes the media sensor for your gap, notch or reflective media application. Note that this is not required if you are using continuous media.

Perform this calibration during initial set-up or after changing your media type. To calibrate:. The printer will begin advancing media; allow at least one label gap or mark to advance under the sensor during this process.

In certain cases, the printer may have trouble differentiating between the label and liner. In addition to directly outputting labels from the printer, there are several optional output configurations available.

With the Internal Media Rewinder option, the printer can wind the printed labels and backing material. To rewind labels:. Tighten the Thumbscrew to secure the retainer in place. Remove the Rewind Retainer and Media Clip. Grasp the end of the hub. While pulling outwardly, squeeze the hub together to collapse it and then slide off the labels. When equipped with the Peel and Present option, labels are dispensed then separated automatically from the liner for immediate application.

Remove all of the labels from the backing material. For on-demand printing, ensure that the Present Sensor has been enabled; see Section 4.

Grasp the hub. Pull the hub outward then squeeze to collapse it and slide off the backing material. When equipped with a Cutter, cut labels are dispensed automatically from the printer. To load media on a cutter equipped printer. For 4. Using the Front Panel. The front panel is comprised of three indicator lights, a Liquid Crystal Display and five mode-dependant keys.

The selectable modes Ready, Menu and Quick Test and the related functions of the printer keys are detailed below. Pressing it again will return the printer to normal operation. Pressing and holding causes the printer to perform a Quick Media Calibration; see Section 3. If yes, the current job is cancelled. The printer remains paused. Pressing and holding four seconds will reset the printer and clear temporary host settings soft reset.

In the Ready Mode, pressing and holding four seconds will change the display contrast. It also decrements numerical values in most menu selections. It also increments numerical values in most menu selections. It also moves between selections within multiple parameter fields. Holding down the key scrolls quantities. During test label printing, this key also functions as a cancel key the printer will prompt you for confirmation before cancellation occurs.

The display provides several types of information:. The time and date, if the printer has received it from one of the following: the host, the front panel setting, or the Time and Date option.

To return the printer to the factory default settings or, if saved, to restore the Factory Setting File:. See Section 4. To return the printer to the factory default settings, and clear all the calibration and adjustment parameters:.

A listing of the factory default settings can be found in Section 4. Printer operation can be controlled through the user interface, allowing the operator access to these six menu system branches:.

Changes made will be saved. When power is removed, the new settings will be restored upon power-up. In addition, as a security feature for the prevention of accidental or unauthorized changes, the menu system has a password protection feature.

Selections denoted with a diamond can only be changed through the menu system - all other selections can be. Welcome to ManualMachine. We have sent a verification link to to complete your registration.

Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. All rights reserved. Printed in the United States of America. Contents Printer Overview 1. Using the Front Panel 4.

Printer Overview 1. I-Class 1. Cutter, Standard Duty A rotary-type mechanism to automatically cut material with a maximum thickness of. I-Class 3.

Internal Rewinder An internal mechanism to wind six-inch outer diameter rolls of printed labels, or the label backing material for the Peel and Present option.

Linear Scanner An integrated fixed-position CCD device featuring bit microprocessor technology for high-speed operation and superior accuracy to ensure the. Peel and Present Mechanism requires the Internal Rewind option An output control device that automatically separates printed labels from the backing material and allows subsequent printing to occur only after the removal of a previously printed label. Present Sensor An output control device that allows subsequent printing to occur only after the removal of a previously printed label.

Thermal Transfer specify configuration at time of order A printing method that uses ribbon to produce exceptional image clarity, as compared to most direct thermal media types. I-Class 5.